Fuse And Fuse Holder Selection: Rating, Breaking Capacity, And Derating

Nov 13, 2026 Leave a message

Jack
Jack
XC Fuse editorial team

XC Fuse / Holder Selection

Rating, breaking capacity and derating: what decides whether a holder survives

The fuse comes from a curve; the holder from mechanical and thermal limits. When a holder overheats at half its rated current, the fuse is rarely the problem.

13 November 2026 8 min read Selection guide

Key takeaways

  • Match the body first: a 5 x 20 holder takes a 5.2 x 20 mm tube, not a 6.35 x 32 mm one.
  • Current and voltage are separate checks; 250 V AC is not a DC rating.
  • The holder does not clear the fault but must survive it - derate for ambient and inrush.

In this article

01 · Fuse body  ·  02 · Current and voltage  ·  03 · Breaking capacity
04 · Curve  ·  05 · Inrush  ·  06 · Derating  ·  07 · Contact
08 · Certification  ·  09 · Acceptance  ·  FAQ

A fuse is chosen from a curve. A holder is chosen from mechanical and thermal limits, and the two lists rarely meet - which is how a fuse holder selection ends up overheating at half its rated current while the fuse was sized correctly.

The checks below follow the order we use before quoting a holder.

01 · Start with the fuse body, then choose the holder

The first check is physical. A 5 x 20 mm holder accepts a 5.2 mm diameter, 20 mm long tube; a 6.35 x 32 mm clip accepts the larger body. A holder that grips loosely runs hot, whatever its rating.

Part Fuse body Published rating Mounting
5x20 fuse holder XC-1 Φ5.2 × 20 mm 6 A, 250 V AC Panel, tool-free fuse change
Fuse clips 5.2 × 20 mm 5.2 × 20 mm 250 V, 10 A, −40 to +90 °C PCB or panel, 0.4 mm copper alloy
Fuse clips 6.35 × 32 mm 6.35 × 32 mm Confirm per model PCB 1.6 mm or screw fixing

The XC-1 body is flame-retardant high-temperature plastic with nickel-plated brass terminals and a stated contact resistance below 10 mΩ. Choose the family - panel, PCB or in-line - from the maintenance plan, then check the numbers.

02 · Current rating and voltage rating are two separate checks

A holder must carry at least the fuse current, but the rating is published under a standard. IEC 60127-6 sets amperage from allowable power dissipation; UL 4248 uses heat-rise limits, so a dual-marked holder can show two maximum currents for one part.

  • Current: holder rating ≥ fuse rating, then apply the derating in section 06.
  • Voltage: the holder must withstand the voltage across the fuse after it opens. AC ratings do not transfer to DC, where there is no zero crossing to quench the arc.
  • Fuse family: a 5 x 20 mm glass fuse covers 0.1–10 A and a ceramic version up to 30 A in the same body, but their interrupting behaviour differs.

If the drawing shows 250 V AC, ask what DC voltage appears on that node during a fault. That is where holders are usually under-specified.

03 · Breaking capacity: the holder must survive the fault the fuse clears

A holder does not interrupt current, so it has no breaking capacity of its own. It still has to contain the arc, gas and pressure of a fuse clearing at its rated breaking capacity.

Standards assign a default short-circuit rating: holders recognised to UL 4248 are typically evaluated at 10 kA, supplemental-fuse holders up to 100 kA, and IEC holders are certified to 60127-5 or 60127-6 by bodies such as VDE or SEMKO.

Rule of thumb

The short-circuit rating of a fuse and holder assembly is its weakest link. A 50 kA cartridge in a 10 kA clip gives you a 10 kA assembly with an expensive fuse.

The scale depends on the family: XC 10 x 38 mm ceramic fuses are published at 10 kA to 50 kA by voltage, up to 150 kA at 500 V on the higher-rated models, and belong in DIN rail bases or PCB mounts, not a 5 x 20 clip.

5x20 fuse holder XC-1 with flame-retardant body and nickel-plated brass terminals

The XC-1 5 x 20 mm holder: 6 A, 250 V AC, flame-retardant body, nickel-plated brass terminals.

04 · Read the time-current characteristic before you fix the holder

The curve decides whether the fuse holds at load and clears at fault. The holder sees only the first half: if the curve allows 135 % for an hour, the holder carries that too.

Test current 5F fast-acting 5T time-lag
150 % ≥ 1 hour ≥ 1 hour
210 % 100 ms – 1800 s 1 s – 120 s
275 % 50 ms – 2 s 600 ms – 10 s
400 % 10 ms – 300 ms 150 ms – 3 s

These are XC 5 x 20 mm glass figures for the 5F and 5T families; 5G, 5S, 5C, 5H and 5CH are published separately and the bands shift with rating. At 210 % the holder carries an overload for up to two minutes behind a 5T fuse, or half an hour behind a 5F.

05 · Inrush, motors and transformers: where holders fail early

Motor starting, transformer magnetising current and capacitor charging draw short currents far above the running load. A time-lag fuse rides through them; the holder has to keep its contact resistance stable through thousands of events.

  • Compare I²t: the melting I²t of the fuse must exceed the inrush I²t of the load with margin.
  • Curve by load: fast-acting for heating and lighting, time-lag for motors and transformers.
  • Repetition: a load switched every few minutes heats the contact spring.

Size the holder to steady current, not starting current, then confirm the temperature rise over a full duty cycle.

06 · Temperature derating: the 80 % rule and what changes it

For fuse holder selection, derating turns a catalogue number into a working answer. UL practice follows fuse derating, around 80 % of rated current, and more with ambient temperature and current cycling. A 6 A holder at 5 A continuous in a closed cabinet is not conservative; it is a calculation nobody did.

  • Up to 40 °C at the holder: the full rating is defensible in free air with one holder.
  • 40–60 °C: plan on about 90 %, typical of a closed cabinet.
  • 60–80 °C: plan on about 80 %, the usual UL-style factor; check the body material limit.
  • 80–90 °C: confirm per model; the published clip range ends at +90 °C, 55–85 % RH.

The bands are guidance, not a curve from a standard. Note which part limits the pair: the 5 x 20 mm glass fuses are rated −55 to +125 °C, the ceramic versions to 125 °C, so the holder usually limits. Measure at the holder, after an hour.

07 · Contact resistance, clamping force and mounting

Most "the holder melted" reports are contact problems in disguise: a current well below the fuse rating can generate enough heat to soften the body, and not always immediately.

  • Stated resistance: the XC-1 quotes below 10 mΩ; ask for the figure and the method.
  • Plating: 0.4 mm copper alloy clips with tin or nickel at 3–5 μm.
  • Clamping force: a spring-only grip relaxes after thermal cycling; check pull-off on a warmed sample.
  • Finger safety: a capped panel holder keeps the fuse away from the operator.

Mounting follows the maintenance plan: panel for external access, PCB clips where the enclosure insulates, in-line along the cable. Confirm wire gauge, terminal torque and board thickness - the clips suit a 1.6 mm board.

08 · Certification: ask for the model and the certificate number

Holder approval is per model, not per brand: a certificate covering the 5 x 20 mm panel holder does not cover the 6.35 x 32 mm clip.

  • Holder standards: UL 4248 and IEC 60127-5 or 60127-6; UL offers recognition to UL 4248 for electronic holders, VDE and SEMKO certify to the IEC standard.
  • Fuse documents: the XC 5 x 20 mm glass fuses state EN/IEC/K/J 60127-1 and 60127-2 plus UL/CSA 248-1, and carry CCC, cULus, VDE, PSE and KC marks on certified models.
  • RoHS and REACH: declarations with the quotation, not after the order.
  • System certificates: TS 16949, ISO 9001 and ISO 14001 describe the quality system, not product approval.

If a quotation claims all safety standards without a model and a certificate number, treat it as unverified until the paperwork arrives.

5x20mm cartridge fuses in fast-acting and time-lag versions

5 x 20 mm cartridge fuses: the curve family must suit the load, and the holder must be rated for the fuse fitted.

09 · Acceptance: what to check when the goods arrive

Incoming inspection is quick if the checklist is fixed before the order: catch a dimension or plating change before the parts are built in.

Item Check Record
Marking Model, current and voltage on part or bag Photo with packing list
Dimensions Fuse fits with light pressure; clip spacing correct Sample measurement sheet
Contact Pull-off force and resistance on a few pieces Sample log with values
Thermal Temperature rise at rated current, in the enclosure Test record with ambient
Documents Datasheet, batch certificate, RoHS/REACH file Quality folder reference

Good fuse holder selection ends with documents that match the parts in the box; keep one sample per batch with its record.

Frequently asked questions

What is the first step in fuse holder selection?

Match the holder to the fuse body: a 5 x 20 mm holder takes a 5.2 × 20 mm tube, a 6.35 × 32 mm clip the larger tube. Then confirm ratings and derate.

Do fuse holders have a breaking capacity?

Not in the fuse sense: the holder does not interrupt current. It is evaluated for short-circuit withstand under UL 4248 or IEC 60127-5/6, typically 10 kA for recognised electronic holders.

How much should a fuse holder be derated?

UL practice follows fuse derating, around 80 % of rated current, and more with high ambient temperature or frequent cycling. Measure the air temperature at the holder.

Why does the holder get hot when the fuse is fine?

Usually contact resistance at the clip or terminal, or a holder above its derated current in a warm enclosure. Check clamping force, plating and terminal torque.

Panel mount, PCB clips or in-line: which one?

Panel mount where the fuse is changed from outside the enclosure, PCB clips where the board is the assembly and the enclosure insulates it, in-line along the cable run.

What documents should come with a holder quotation?

The datasheet for the exact model, the certificate number against the standard, a batch certificate and RoHS/REACH declarations. Send the fuse rating and drawing and we will confirm it.

Next step

Send the fuse rating and the drawing. We will confirm the holder against both.

Send the fuse size and rating, circuit voltage (AC or DC), ambient temperature, mounting style and panel cut-out or PCB footprint. XC will reply with the holder model, its ratings, the certificate reference and packing data.

Email sales07@xcfuse.com or use the inquiry form. You can review the fuse holders range, the 5x20 fuse holder, the fuse clips or the matching cartridge fuses.

Request a holder and fuse review